Caseless ammunition CAR rifle Flemish weapons project 1990

Could the NATO ammunition shortage caused by the war in Ukraine bring the projects for caseless ammunition back to Flanders? 

In 1989, the German company Heckler & Koch, in collaboration with Dynamite Nobel, presented the G11 rifle with caseless ammunition, with the aim of replacing the G3 battle rifle in the German army.

The G11 patents have expired

Recently, the patents for the German G11 weapon system with caseless ammunition have expired, leading several weapon manufacturers to re-examine the concept of caseless ammunition. Caseless ammunition is thus back in the spotlight! 

The concept of the G11 weapon and ammunition was considered revolutionary, but in Flanders, this G11 project raised doubts about the operating principle.

 The G11 has a plastic outer frame with a metal firing unit that is mounted on springs and moves as a whole with every shot. This has a number of predictable negative properties such as: 

  • To allow that firing unit to move, there is a play that ultimately has a negative impact on the accuracy of the weapon. This inaccuracy was proposed as a solution to better hit the target with that spread in 3-shot burst mode. This also means that with a single shot, the spread is present, making the precision unpredictable. 
  • The entire firing unit with barrel, frame, trigger mechanism and loaded magazine means a large mass that moves with every shot and thus disrupts the balance of the weapon.
  • The entire firing unit with barrel, frame, trigger mechanism and loaded magazine has a heavy mass that is set in motion by the recoil impulse and ultimately causes greater recoil.

The predictable negative properties led in the late 1980s to the development of the  C.A.R. project (Caseless Ammunition Rifle) which was started by Rik Van Bruaene in Roeselare (West Flanders Belgium). This blog was compiled based on a number of photos from the old box of the Flemish C.A.R. project. 

Van Bruaene Rik metalworking

Flemish company from Roeselare, Van Bruaene Rik metalworking in 1990 worked as a weapons engineering design bureau under the name VBR-Gundevelopment.

C.A.R. project (Caseless Ammunition Rifle) by VBR-Gundevelopment

The C.A.R. project is characterized by the use of a fixed frame and that only the parts necessary for the functioning of the weapon move. This allows us to avoid the problem with the play and the precision of the weapon and the imbalance caused by the large number of moving parts. 

The frame block of the CAR clamped in the lathe to accurately turn the housing of the roller drum bolt in the old workshop of Van Bruaene Rik in Roeselare. 

                                                                                 

The entire firing unit mounted in the frame block of the CAR. 

The firing unit is thus assembled around a fixed frame block, so there is no play on the barrel. A fixed barrel therefore always has the same accuracy with every shot, just like another rifle with a fixed barrel. 

Photo of the CAR-2 during the development of the project.

The same firing unit with two different mounts for the magazines and muzzle flash hider. A flash hider with two legs for long magazines and a flash hider for short magazines.

The C.A.R.-1 with two legs as a support weapon with a magazine capacity of 120 shots. 

The designer Rik Van Bruaene with the prototype C.A.R.-1 from VBR-Belgium 1990

The C.A.R.-1 prototype that can be used as an assault rifle and support weapon and where every soldier has an immediately available firepower of 120 shots. The consideration was made as to whether it is responsible to give every soldier magazines with a firepower of 120 rounds? This is a fully automatic weapon with which, just like in Vietnam, it will be sprayed. The ammunition supply that would be needed for this would be considerable and could cause supply problems. On top of the weapon is a dovetail mount where different types of sights can be attached.   

The designer Rik Van Bruaene with the prototype C.A.R.-2 from VBR-Belgium 1990

The C.A.R.-2 prototype assault rifle had a shorter magazine with a firepower of 75 rounds. Because no heavy muzzle flash hider with two legs was attached, that prototype is considerably lighter and more maneuverable than the C.A.R.-1.

The notorious "Ghost" of a roller drum bolt.  

Feeding a brass dummy round into the C.A.R. with a feeding hook.

During the testing of the cartridge feeding of the C.A.R. prototype where a brass dummy round  was fed through the feeding hook into the roller drum bolt, a severe blockage occurred. A piece of metal was carried along with the roller drum bolt and was stuck between the roller drum and the frame, which caused the entire rotating system to block at an angle of 45° with the dummy round enclosed in a completely sealed chamber. 

If this blockage had occurred with a live caseless ammunition round in an overheated chamber, then the cook-off problem could have caused a catastrophic explosion of the weapon which is inherent to a 90° rotating roller drum bolt. This means that the theoretical danger zone where a cartridge is fed perpendicular to the barrel axis and then must rotate 90° to bring the cartridge in line with the barrel, is a fact. This situation was called the "Ghost" in the 90° rotating roller drum bolt which can manifest in an overheated chamber where the cartridge can come to ignition by self-ignition in a completely sealed chamber. This creates a danger zone that cannot be worked out in the 90° rotating roller drum bolt. 

The frame of the C.A.R. open with the roller drum bolt visible. 

The blockage of the 90° rotating roller drum bolt was in this case caused by a small piece of brass from the dummy round, but could just as well have been caused by sand being fed with the cartridge into the roller drum bolt. Such a dangerous blockage is inherent to the system that is used by the C.A.R. and the G11.  

Although the German G11 rifle with caseless ammunition and 90° rotating roller drum bolt was approved by the German army and there is no mention of a catastrophic blockage during testing, a possible dangerous situation is theoretically possible where the weapon can explode. 

Given that such a dangerous situation occurred so early in the testing stage of the C.A.R., it is almost inconceivable that Heckler & Koch was not aware of this dangerous situation in the G11 roller drum bolt mechanism.

Heckler & Koch continued to work with the G11 weapon and caseless ammunition system for a long time, where it is clearly visible in the tests that the weapon was demonstrated in extremely clean conditions and where the caseless ammunition was stored in a dust-tight plastic tube. Sand in the mechanism of the G11 could be fatal for the G11 weapon. 

Rik Van Bruaene immediately stopped with this type of locking after the blockage of the 90° rotating roller drum bolt and all feeding systems where the cartridge is not immediately fed in line with the barrel axis were considered unsafe. 

The C.A.R.-2 and the CASMG from VBR-Belgium ( Caseless Ammunition Sub Machine Gun )

After the C.A.R. project, a new project with caseless ammunition was started where the cartridge is immediately fed in a straight line with the barrel axis. The project falls earlier under the class of pistol machine guns but theoretically does not have a "Ghost" danger zone. Several other calibers of caseless ammunition projects were started, including a 5.7x19mm caseless ammunition project. The projects with caseless ammunition were not further developed after the visit to Dynamit Nobel.   

During the visit of Rik Van Bruaene to Dynamit Nobel, it became clear that something was not right. The development of caseless ammunition at Dynamit Nobel was completely financed by the German government. The development had cost Dynamit Nobel not a single euro and the subsidies for the development were stopped by the German government. As a result, the entire caseless ammunition project was stopped. 

This does not mean that there is no longer interest in caseless ammunition.

As major advantages of the weapon and caseless ammunition system were put forward:

  • Reducing the use / supply of brass. 
  • Reducing production time and machines.
  • Reduction of the volume and weight of the ammunition.
  • Reduction of the dependence on foreign raw materials such as copper and zinc to make the brass casings.
  • More efficient weapon and ammunition.

Now that new weapon and ammunition systems are being developed everywhere, is the question whether such weapon systems can be further developed in Flanders? 

The prototypes were lost during the sale and the breaking up of the old workshop of Van Bruaene Rik. Only the old photos still bear witness that weapon developments were ever done in Flanders. 

Protection against war weapons

Discrete Flex-Pro discrete bulletproof vest 3A NIJ 0101.06

 This light and thin discrete bulletproof 3A has internal pockets in which hard bulletproof plates can be pushed in if you want protection against war weapons. 

Superlight discrete bulletproof vest class 3++ICW

This superlight discrete bulletproof vest contains soft bulletproof packages 3A and two hard bulletproof plates class 3++ that offer protection against bullets from Kalachnikov rifles. 

Compact bulletproof Molle vest 3A MT-PRO GEN7+NIJ-4 ICW

This compact 3A MT-PRO GEN7 bulletproof vest is a soft bulletproof vest with two hard bulletproof plates class 4 ICW that can stop bullets from rifles.

Modern bulletproof vest with extra NIJ-4 class protection ICW

This blue bulletproof vest with extra protection on the neck, shoulders, upper arms and groin is class 3A and offers protection against bullets from handguns and shrapnel, with an additional two class 4 ICW bulletproof plates for protection against rifle bullets. It is the most efficient protection in a war zone against rifles and drones.  

Also visit our English-language page "is caseless ammunition coming back"